TECHNICAL DATAANDSERVICE MANUALCOMPOUND MITER SAW C 10FCH2C 10FCE2SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENTLIST No
--- 7 ---7. PRECAUTIONS IN SALES PROMOTIONIn the interest of promoting the safest and most efficient use of the Models C 10FCH2 and C 10FCE2 Compoun
--- 8 ---(2) Caution label (A) (at the front of the hinge) (only the Model C 10FCH2)Do not stare into laser beam. If your eye is exposed directly to
--- 9 ---7-3. Relative StandardsStandards, regulations and guidelines for the safe use of laser equipment[USA] FDA CDRH 21 CFR[AUS/NZL] AS/NZS 2211.
--- 10 ---7-5. Ambient Illuminance and Visibility of Laser Line (Only the Model C 10FCH2)The visibility of the laser line on the workpiece changes d
--- 11 ---Ink lineSaw bladeFig. 7WARNING:Before plugging the power plug into the receptacle, make sure that the main body and the lasermarker are tu
--- 12 ---CAUTION:Laser radiation - Do not stare into beam.Laser radiation on work table. Do not stare into beam. If your eye is exposed directly
--- 13 ---8-3. Confirmation for Use of Sub Fence (B)The Models C 10FCH2 and C 10FCE2 are equipped withsub fence (B). Use sub fence (B) for miter cut
--- 14 ---8-4. Cutting Operation(1) Cutting efficiency will be reduced if a dull saw blade is used, if an excessively long extension cord is used, o
--- 15 ---For miter cut settingIf the turn table has been set to either of the angles described, move the turn table adjusting side handle alittle t
--- 16 ---(1) Setting to cut crown molding at positions and in Fig. 14 (See Fig. 15, tilt the head to the left.):Turn the turn table to th
REMARK:Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol(s)is(are) used in the place of company name(s) and model name(s)
--- 17 ---Cutting method of crown molding without tilting the saw blade6 mm wing boltCrown molding stopper (L)(optional accessory)Crown molding stop
--- 18 ---9. ADJUSTMENT OF COMPONENTS9-1. Bevel Angle AdjustmentBefore the power tool is shipped from the factory, it is adjusted for 0û and left 45
--- 19 ---Base packingPacking (D)Packing (F)Fig. 25Fig. 24Packing (F)Carton boxPacking (B)Packing (C)Fig. 26Fig. 23Packing (C)Packing (B)Packing (E)
--- 20 ---11. PRECAUTIONS IN DISASSEMBLY AND REASSEMBLY11-1. Precautions in Disassembly and Reassembly of the Laser Marker (Only the Model C 10FCH2)
--- 21 ---1. Remove the four Bolts M8 x 35 [46], Spring Washers M8 [47] and Bolt Washers M8 [48], then remove Fence(A) [65] and Fence (B) [54].2. Lo
--- 22 ---B. Armature ass'yCord, stator ass'y and housing ass'yTools required: • Phillips screwdriver • Flat-blade screwdriver • Plas
--- 23 ---1. Remove the two Tapping Screws (W/Flange) D4 x 25 (Black) [151] and the four Tapping Screws (W/Flange)D4 x 20 (Black) [152], then remove
--- 24 ---C. Safety cover and linkSpindle and springTools required: • Phillips screwdriver • Hex. bar wrench 4 mm • Hex. bar wrench 3 mm • Box wrenc
--- 25 ---1. Remove the Machine Screw M4 x 8 [131] at the notched side of the Spindle Cover [130] and slide the SpindleCover [130] to remove the TCT
--- 26 ---1. Remove the two Tapping Screws (W/Flange) D4 x 25 (Black) [151] and the four Tapping Screws (W/Flange)D4 x 20 (Black) [152], then remove
PageCONTENTS1. PRODUCT NAME ...
--- 27 ---11-3. ReassemblyReassembly can be accomplished by following the disassembly procedures in reverse. However, specialattention should be gi
--- 28 ---11-4. Wiring DiagramCarefully ensure that wiring is accomplished as illustrated below. As incorrect wiring will result in lack of rotatio
--- 29 ---Fig. 32-2C 10FCH2 Europe (230 V areas)/AUSC 10FCH2 Europe (110 V areas)Fig. 32-3
--- 30 ---Fig. 33-2Fig. 33-1 C 10FCE2 USA/CAN C 10FCE2 Europe (230 V areas)/AUSFig. 33-3 C 10FCE2 Europe (110 V areas)
--- 31 ---Fig. 33-4 C 10FCE2 Asia/South America
--- 32 ---Fig. 34-1 C 10FCH2 USA/CAN2Actual wiring diagram C 10FCH2 Europe/AUS/NZL/China/Hong KongFig. 34-2
--- 33 --- C 10FCE2 USA/CAN C 10FCE2 Europe/AUS/NZL/Asia/South AmericaFig. 35-1Fig. 35-2
--- 34 ---11-5. No-load CurrentAfter no-load operation for 30 minutes, the no-load current values should be as follows.11-6. Reassembly Requiring Ad
--- 35 ---Tolerance0.38/220 (0.016"/8-5/8")0.4/height of fence (0.016"/height of fence)0.1 (0.004")0.4/100 (0.016"/4")
--- 36 ---11-9. Adjustment of Laser Marker Accuracy (Only the Model C 10FCH2)(1) Construction of laser marker and functions of each componentLaser h
--- 1 ---1. PRODUCT NAMEHitachi Compound Miter Saw, Models C 10FCH2 and C 10FCE22. MARKETING OBJECTIVEThe new Models C 10FCH2 and C 10FCE2 are relea
--- 37 ---Hex. bar wrench(2.5 mm)(2) Adjustment of squareness with the fence surfaceThe laser line inclines to the left by turning the hex.socket se
--- 38 ---(4) Adjustment of the laser markerAdjust the laser marker according to the following steps from to .Adjust the product accuracy
--- 39 ---11-10. Tightening Torque(1) Model C 10FCH2• Seal Lock Hex. Socket Set Screw M6 x 10 [3] 43.4 in-lbs. (4.9 N•m, 50 kgf•cm)• Machine Screw (
--- 40 ---(2) Model C 10FCE2• Machine Screw (W/Washers) M6 x 20 (Black) [4] 43.4 in-lbs. (4.9 N•m, 50 kgf•cm)• Machine Screw (W/Sp. Washer) M5 x 16
--- 41 --- a Inaccuratesquareness betweenthe turn table and thesaw blade causes thesaw blade to cut intothe workpiece at anangle. b Excessive defl
--- 42 ---0.1/height of fence(Fig. 50)------------------------ f Inaccurate squarenessbetween the fenceand the turn table and/or the base cau
--- 43 ---• Same as the Item 1- b .• Repair impact marks orscratches on Washer (D) [101]or replace them as necessary.• Same as the Item 1- a .•
--- 44 ---a Excessively fastcutting speedb Core diameter ofextension cord is toosmall.c Excessive cutting forceis applied due to dullsaw blade.d
--- 45 ---a Improper wiringb Switch (A) failurec Switching powersupply failured Laser holder failurea Switching powersupply failureb Laser mo
--- 46 ---13. STANDARD REPAIR TIME (UNIT) SCHEDULESMODEL 10 20 30 406070 min.50FixedVariableC 10FCH2Work FlowSwitch Handle(A)LinkLower Guard (B)Lowe
--- 2 ---4-1. Selling Point Descriptions(1) Laser guide system (Only the Model C 10FCH2)Use the laser marker for aligning with the ink line on thewor
--- 47 ---MODEL 10 20 30 406070 min.50FixedVariableC 10FCE2Work FlowSwitch Handle(A)LinkLower Guard (B)Lower Guard (A)Return SpringSwitchLock LeverH
ELECTRIC TOOL PARTS LISTLIST NO. E945COMPOUND SAWModel C 10FCH22006 • 10 •11(E1) Hitachi Power Tools1345678910111213141516171822233332302526212
--- 2 --- 10 -- 06C 10FCH210010110310110410510610710810911111511211312011812112212311711612412512612812912713013113213313213313413513613714214314414
* ALTERNATIVE PARTS --- 3 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS10 -- 06C 10FCH21 326-748 LASER HOLDER 1 INCLUD. 22 CAUTION LABEL (A) 13 3
* ALTERNATIVE PARTS--- 4 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS10 -- 06C 10FCH252 949-342 FLAT HD. SCREW M6X25 (10 PCS.) 153 326-704 SUB
* ALTERNATIVE PARTS --- 5 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS10 -- 06C 10FCH2* 128 877-371 NYLON NUT M5 1 FOR EUROPE* 129 949-236 MACHI
* ALTERNATIVE PARTS--- 6 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS10 -- 06C 10FCH2* 168 360-695F ARMATURE ASS’Y 240V 1 INCLUD. 169-172169 62
OPTIONAL ACCESSORIESITEMNO.CODE NO.DESCRIPTION REMARKSNO.USED* ALTERNATIVE PARTS --- 7 ---10 -- 06STANDARD ACCESSORIESITEMNO.CODE NO.DESCRIPTION REM
--- 8 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USED10 -- 06C 10FCH2Printed in Japan(061011N)
ELECTRIC TOOL PARTS LISTLIST NO. E946COMPOUND SAWModel C 10FCE22006 • 10 •11(E1) Hitachi Power Tools3456789101112131415161822233332302526212728
--- 3 ---(5) Large table for increased material stabilityThe turn table is as large as that of the Model C 10FCH.C 10FCH2/C 10FCE2C 10FCH/C 10FCEOut
--- 2 --- 10 -- 06C 10FCE210010110310110410510610710810911111512011812112212311711612412512612812912713013113213313213313413513613714214314414514614
* ALTERNATIVE PARTS --- 3 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS10 -- 06C 10FCE2 3 307-956 SEAL LOCK HEX. SOCKET SET SCREW M6X10 1 4 323
* ALTERNATIVE PARTS--- 4 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS10 -- 06C 10FCE255 326-705 HOLDER 156 322-901 LINER (A) 257 322-964 LINER
* ALTERNATIVE PARTS --- 5 ---ITEMNO.CODE NO.DESCRIPTIONREMARKSNO.USEDPARTS10 -- 06C 10FCE2* 134 301-806 WING BOLT M6X15 1 FOR EUROPE* 135 322-950 SP
* ALTERNATIVE PARTS--- 6 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USEDPARTS10 -- 06C 10FCE2* 176 340-686C STATOR ASS’Y 120V 1 INCLUD. 177* 176 340-68
OPTIONAL ACCESSORIESITEMNO.CODE NO.DESCRIPTION REMARKSNO.USED* ALTERNATIVE PARTS --- 7 ---10 -- 06STANDARD ACCESSORIESITEMNO.CODE NO.DESCRIPTION REM
--- 8 ---ITEMNO.CODE NO.DESCRIPTION REMARKSNO.USED10 -- 06C 10FCE2Printed in Japan(061011N)
--- 4 ---No-load rotation speed 5,000 min-1Full-load currentType of motorAC single phase commutator series motor255 mm (10") external dia.5. SPE
--- 5 ---255 mm (10") TCT saw blade (60 teeth, Code No. 976472)••••••••••••••• for normal cutting255 mm (10") TCT saw blade (100 teeth, C
--- 6 ---255 (10")5,0001,5201,950 C 10FCH C10FCE Provided Not provided 1 mWDouble insulation280 (11-1/32")Provided (fixed)250
Comentarios a estos manuales