RIDGID metal detector Guía de usuario Pagina 122
- Pagina / 144
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Logs and Reports
■ Problem: Bin full - the reject bin full sensor has been blocked for longer than 5 seconds and
the transport system has stopped. The bin will need to be emptied before the transport can be
restarted.
o
Action:
If the bin is full:
1. Remove, identify and segregate the product. Once the sensor is unblocked the fault
will automatically clear.
If the bin is not full:
1. Check the Bin full sensor is working correctly.
■ Problem: Link corrupted - data corruption has occurred between the detector and LomaLink
PC or other controlling device. The operation of the detector is unaffected.
o
Action:
1. Check cabling and link connectors from remote device.
2. Check LomaLink PC or other controlling device for reported errors.
■ Problem: Link failure - a break in communication between the detector and LomaLink
PC/other controlling device. The operation of the detector is unaffected.
o
Action:
1. Check cabling and link connectors from remote device.
2. Check connections between the detector and LomaLink PC or other controlling device
for loose or broken wiring/connectors.
■ Problem: PV test timeout - an automated prompt for the PV test has either not been actioned
or completed within the window time set. The transport system may have stopped.
o
Action: Clear system fault (restart the transport if stopped) and perform a PV test.
■ Problem: PEC obstructed - the product registration photo-eye has remained blocked for
greater than 6 consecutive pack lengths. This fault is only generated if the PEC fault is
enabled.
o
Actions:
1. Check the PEC for blockage.
2. Check the PEC is working correctly.
3. Check pack flow length entry is adequate in the Menus > Set Up > Product menu,
ensuring an allowance is made for pack skew.
4. Ensure the correct belt speed is entered in the Menus > Service > Configuration >
System menu..
■ Problem: Wrong flash c/sum - the software has compared the flash checksum currently
stored in its memory with the checksum for recently installed software. This occurs if a
software update has been done and a hardware cold start was not performed after
installation.
o
Action:
1. Perform an update to the Flash Checksum in the Menus > Machine Details menu.
112
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Relacionado con productos y manuales para De medición, control y control RIDGID metal detector
(5 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.385 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales