RIDGID MS 1290 Guía para resolver problemas Pagina 7
- Pagina / 56
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7
Plan The Way You Will Hold The Workpiece From Start To Finish.
• Avoid awkward operations and hand
positions where a sudden slip could
cause fingers or hand to move into
the blade.
• Don’t Overreach. Keep good foot-
ing and balance.
• Keep your face and body to one
side of sawblade, out of line with a
possible thrown piece.
• Cut only one workpiece at a time.
• Never cut Freehand:
- Brace your workpiece solidly
against the fence and table top so
it will not rock or twist during the
cut.
- Make sure there’s no debris
between the workpiece and its
supports.
- Make sure no gaps between the
workpiece, fence and table will let
the workpiece shift after it is cut in
two.
• Keep the cut off piece free to move
sideways after it's cut off. Otherwise,
it could get wedged against the
blade and thrown violently.
• Clear everything except the work-
piece and related support devices
off the table before turning the miter
saw on.
• Secure Work. Use clamps or a
vise to help hold the work when it’s
practical.
Use extra caution with large, very
small or awkward workpieces:
• Use extra supports (tables, saw
horses, blocks, etc.) for any work-
pieces large enough to tip when not
held down to the table top.
• Never use another person as a sub-
stitute for a table extension, or as
additional support for a workpiece
that is longer or wider than the basic
miter saw table or to help feed, sup-
port or pull the workpiece.
• Do not use this saw to cut pieces
too small to let you easily hold the
work while you keep the thumb side
of your index (pointer) finger against
the outside edge of the fence.
• When cutting irregularly shaped
workpieces, plan your work so it will
not slip and pinch the blade and be
torn from your hands. A piece of
molding, for example, must lie flat
against the table or fence, or be held
by a fixture or jig that will not let it
twist, rock or slip while being cut.
• Properly support round material
such as dowel rods, or tubing. They
have a tendency to roll while being
cut, causing the blade to "bite." To
avoid this, always use a fixture
designed to properly hold your
workpiece.
Whenever Saw Is Running
WARNING: Don't allow familiarity
(gained from frequent use of
your miter saw) cause a careless
mistake. A careless fraction of a
second is enough to cause a
severe injury.
Before starting your cut, observe the
miter saw while it runs. If it makes an
unfamiliar noise or vibrates exces-
sively, stop immediately. Turn the saw
off. Unplug the saw. Do not restart
until finding and correcting the prob-
lem.
Keep Children Away. Keep all visi-
tors a safe distance from the miter
saw. Make sure bystanders are clear
of the miter saw and workpiece.
- Table of Contents 2
- Safety Signal Words 3
- Before Using The Saw 3
- Before Each Use 4
- Preparing to Make Cut 6
- Before Leaving The Saw 8
- Assembly 13
- Assembly (continued) 14
- Four Basic Saw Controls 15
- Alignment (Adjustments) 17
- (Miter Alignment) 18
- Miter Lock Lever Adjustment 20
- Bevel Lock Lever Adjustment 21
- Mounting The Miter Saw 22
- Dress For Safety 24
- Preparing to Make the Cut 25
- Whenever Saw Is Running 26
- Before Leaving The Saw: 26
- Basic Saw Operations 27
- Chop Cutting 28
- Body and Hand Position 28
- Miter Cut 29
- Miter Scale Usage 29
- Bevel Cut 29
- Sliding Fence 29
- Cutting Bowed Material 30
- WARNING: Avoid thrown 31
- Workpiece Support 32
- Auxiliary Fence 32
- Rough Cutting A Dado 33
- Cutting Base Moldings 33
- Cutting Crown Moldings 34
- Support Jig 35
- degrees 36
- Maintenance and Lubrication 38
- Lubrication 39
- Motor Belt Tension 39
- Accessories 40
- Using Carbide Tipped Blades 40
- Troubleshooting Guide 41
- Wiring Diagram 42
- Repair Parts 44
- CALL 1-800-4-RIDGID 56
Relacionado con productos y manuales para Tronzadoras RIDGID MS 1290
Tronzadoras RIDGID MS1250LZ1 Manual del operador
(34 paginas)
(34 paginas)
Tronzadoras RIDGID AC9944 Manual del operador
(38 paginas)
(38 paginas)
Tronzadoras RIDGID MS255SR Manual de uso y cuidado
(36 paginas)
(36 paginas)
Philips FWM75/22 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Philips FWM75/22.
Nous fournissons des manuels en pdf 3 Philips FWM75/22 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales