RIDGID RD80770 Manual del operador Pagina 1

SAVE THIS MANUAL FOR FUTURE REFERENCEYour pressure washer has been engineered and manufactured to our high standard for dependability, ease of operati

10ASSEMBLYFig. 3fraMe SuppOrtINSTALLING THE FRAME SUPPORTSSee Figure 3.n Locate the frame supports, hex bolts (2 long and 2 short), and hex nuts.n

11ASSEMBLYSpray waNdtrIGGer haNdleGrOOVed GrIppING SurfacecONNectOrFig. 5INjectION hOSe fIttINGINjectION hOSeFig. 7CONNECTING THE HIGH PRESSURE HOSE

12ADDING LUBRICANT TO THE ENGINESee Figure 8.NOTE: This machine has been shipped with approximately 2 oz. of lubricant in the engine from testing. You

13ASSEMBLYquIck-cONNect cOllarCONNECTING THE GARDEN HOSE TO THE PRESSURE WASHERSee Figure 10.The water supply must come from a clean wate

14OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to

15OPERATIONrecOIl StarterrecOIl StarterthrOttle leVer CAUTION :Do not run the pump without the water supply con-nected and turned on as this will res

16OPERATIONFig. 16 WARNINGNever direct water stream towards people or pets, or place any part of the body in the stream path as this may cause inject

17OPERATIONFig. 17 WARNINGNever lift or carry this machine using the moving handle. Do not move this machine by pulling on the hoses.MOVING THE P

18OPERATIONUSING THE PRESSURE WASHERSee Figure 19.nTurn off the pressure washer and shut off the water supply. Pull trigger to release wat

19MAINTENANCE WARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

2TABLE OF CONTENTSnIntroduction...

20MAINTENANCEFig. 22STORING THE PRESSURE WASHERSee Figures 21 - 22.It is important to store this product in an area that will not experience freezing

21MAINTENANCEPE R IODI C MA I NTEN A NCE S C HEDU L E TABLEServicing requires extreme care and knowledge and should be performed only by a qua

22TROUBLESHOOTING PROBLEM CAUSE SOLUTIONEngine fails to start 1. Engine switch is in the off position.

23WARRANTYEVAPORATIVE EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSYour new RIDGID® brand gasoline powered product complies

24WARRANTYDEFECTS WARRANTY REQUIREMENTS:(a) The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.(b)

25WARRANTYProof of purchase must be presented when requesting warranty service.This product is manufactured by Techtronic Industries North Ame

26CUSTOMER SERVICE INFORMATIONFor parts or service, contact your nearest RIDGID® authorized service center. Be sure to provide all relevant informatio

3IMPORTANT SAFETY INSTRUCTIONS WARNING:Read and understand all instructions. Failure to follow all instructions listed below, may result in el

4SPECIFIC SAFETY RULESn Never direct a water stream toward people or pets, or any electrical device.n     c

5SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols wil

6SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we s

7FEATURESFig. 1PRODUCT SPECIFICATIONSEngine Size ...

8FEATURESKNOW YOUR PRESSURE WASHERSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in this opera

9ASSEMBLYUNPACKINGThis product requires assembly.n Carefully cut the box down the sides then remove the machine and any accessories from the box.